steering wheel compatible with nrg quick release kit

#Steering wheel compatible with nrg quick release kit full
#Steering wheel compatible with nrg quick release kit plus

#Steering wheel compatible with nrg quick release kit full

So in essence, 1.5″ more offset than where I was at and a full 1.75″ more offset than a stock Miata. Note: The NRG Quick Release 2.0 Dimensions: 2.5″ deepĢ.25″ MOMO hub + 1″ spacer/converter + 2″ Nardi Deep Corn 330mm = 5.25″ offset.Ģ.25″ MOMO hub + 2.5″ NRG QR + 2″ Nardi Deep Corn 330mm = 6.75″ offset. Don’t tell me that hasn’t happened to you.

#Steering wheel compatible with nrg quick release kit plus

Plus there is always the benefit of not ripping into the nice Nardi wheel’s leather with jean pocket studs as you get in and out of the car. Ingress and egress is easier with the steering wheel off. There is absolutely no slop, the engagement and disengagement is assertive and confidence inspiring. The NRG Quick-Release 2.0 is quite well-built and well designed. The position is much more like a track car, but still not even close to race car. If you use a short hub like the NRG short hub, the position will be considerably closer to stock. Regardless, keep in mind this is because I insisted in using the deeper MOMO hub because of its crushable design.

For now, I’ll get used to them as they are. I’m aware some guys modify those and bend them a bit closer. The main issue I found is that now it requires quite a reach to actuate the signal and wiper stalks on the steering column. It’s OK and I’m going to attempt to get used to it. 1.5″ in increased offset is actually quite a lot. The steering wheel feels much closer to me than I expected. If you switch out your stock Miata steering wheel, whether you’re using a converter or not, you’re more than likely going to have to fine tune your tie-rods to center your steering wheel.Ģ. I’ve concluded it just comes with the territory. I’m still going to have to adjust the tie-rods to center the thing. I couldn’t get the steering wheel perfectly straight using this setup, but it is much closer to center now. Given I insist on the MOMO hub and not the NRG short hub, the steering wheel is slightly closer to me than if I were using the NRG QR 2.0/NRG Short Hub setup.Īfter installing the NRG QR, which took much longer than it should’ve – not the quick-release’s fault but rather that I had to remove the MOMO hub with an improv puller and it took me forever – I noted a few things.ġ. The NRG Quick-Release is 2.5″ thick, so it would put the steering wheel another 1.5″ towards me. I just might be able to get the wheel centered using that and not have to fiddle too much with the tie rods. I would have to center it by adjusting the tie rods under the car.īefore I went ahead and did that I decided to remove the spacer and give the NRG steering Quick-Release for Miata a shot. However, given the spacer is a MOMO to NARDI converter, it put the wheel slightly off center because if the offset bolt pattern. My offset setup was 2.25″ hub + 1″ spacer converter + 2″ steering wheel = 5.25″ (stock is 5″). Long story short, I was running a 1″ spacer on a MOMO hub for Miata to get the steering wheel a bit closer to me for a more sporty driving position. The part number for this version and color combo is SRK-200BK. NRG might make a different hub-end bolt pattern but I’m not sure. That side only had one bolt pattern, so be sure to double check for fit. The hub side of the QR worked perfectly with my MOMO hub. The steering wheel side of the quick release works with both MOMO and Nardi bolt patterns. So long as you have a hub boss that will fit the bolt pattern. The quick release is a bit more of a universal part. In the title I say, “NRG Quick Release for Miata.” But generally, it’s the hub that needs to fit the Miata and not the QR itself. Finally, I decided to put my part snobbery aside and go with the NRG Innovations unit. Thing is, the Works-Bell QR is about 3 times the price of the NRG QR 2.0 and I somehow always found better ways to spend my money. I had held out for a while as I really wanted a JDM Works-Bell quick release. It’s the simple black version QR with titanium rim. I recently acquired a NRG Quick-Release 2.0 for the RallyWays Miata. The NRG QR 2.0 is installed between a MOMO hub for Miata and a Nardi Deep Corn 330mm steering wheel. Here we look at using a NRG Quick Release 2.0 on the RallyWays Miata.